溫控開關，溫控器工作原理(Operation Principle)

KSD301系列突跳式溫控器(簡稱:KSD301溫控器)是小型帶外殼的雙金屬片溫控器．屬溫度繼電器類器件。利用碟型雙金屬片在溫度作用下產生瞬間跳動的原理．通過機構的作用。使觸點迅速動作，達到斷開或接通電路的目的。其工作溫度固定，無須調整：動作可靠干脆．電弧??；使用壽命長；無線電干擾少。
KSD301 snap action thermostat series is a small-size bimetal thermostat series with a metal cap，which belongs to thermal relays’family．The main principle is that one function of bimetal discs ls snap action under the change of sensing temperature．The snap action of disc can push the action of the contacts through the inside structure，then caused on or Off of the circit finally．The main characteristics are the fixation of working temperature，the reliable snap action，less flashover，longer working life and less radio interfernce

注意事項(Cautions)

1、溫控器應工作于空氣相對濕度不大干90％、無腐蝕性氣體、可燃性氣體和導電塵埃存在的一般室內環境。
2、溫控器采用接觸感溫時。應使其封蓋緊貼被控器具的發熱部位。并應在封蓋感溫表面涂上導熱硅脂或其他性能類
似的導熱介質。
3、不可把封盞頂部壓塌或使其變形。以免動作溫度改變或影響其他性能。
4、不得讓液體滲入溫控器內部，殼體必須避免受到過大的力以防止出現裂紋；殼體應保持清潔。防止導電物質污染， 以免應絕緣性能降低而發生短路擊穿。
5、手動復位產品在復位時力量不可過大，以刑能按下復位柄為宜。一般應小于20N，以免損壞溫控器內部結構。
6、使用過程不能折彎接線端子。否則將影響電氣連接的可靠性。
1．The thermostat should work in environments with humidity not higher than90％．free of caustic．flammable gas and conducting dust．
2．When the thermostat is used to sense the temperature of solid items．its covel should be clung to the heating part of such items．Meanwhile．heat-comducting stilicon grease or other media of similar nature should be applied in to the cover surface。
3．The top of the covel must not be pressed to sink or be distored so as to avoid adveres effect on the thermostat’s temperature sensitivity or its other functions．
4．Liquids must be kept out of the Thermostat’s inner part，The base must avoid any foree that could lead to crack；it should be kept clear and away from the pollution of electric substance to prevent insulation weakening that leads to shortclrcuited damages．

技術參數(Technical Apecmcations)

額定電氣參數：5A系列AC250V 5A/AC120V 7A (阻性負載)
　　　　　　　10A系列AC250V 10A(阻性負載)
　　　　　　　16A系列AC250V 16A(姐性負載)
常態電氣強度：AC50Hz2000V歷時一分鐘不擊穿．無閃絡
常態絕緣電阻：大于100M0 -（500V兆歐表測量）
接點形式：單刀單擲(S.P.S.T),分為三種類型：
　　　　　1．窒溫下接通，溫度上升觸點斷開，溫度下降觸點接通
　　　　　2．室溫下斷開，溫度上升觸點接通，溫度下降觸點斷開
　　　　　3．室溫下接通。溫度上升觸點斷開。手動復位接通
接地方式：通過溫控器金屬外蓋與設備接地金屬部件相連
Electric Ratings：AC250V 5A/AC120V 7A(Resistive load)
　　　　　　　AC250V 10A(Resistive load)
　　　　　　　AC250V 16A(Resistive load)
Electric Strength：No breakdown and flashover underAC 50Hz 2000V for one minute
Inslation Resistance：>1OOMQ(with a DC500V megger)
Contacts Form：S．P．S．T．Division to three types：
1．Closes in room temperature．Opens at temperature rise。colses at temperature decreasing。
2．Opens in room temperature．Closes at temperature rise．Opens at temperature decreasing．
3．Closes in room temperature．Opens when the temperature rise．closes at temperature decreasing．
The action of close will be fin ished through manual reset．
Earthing Methods：by the connection of the metal cap of thermostat and the earth-connect metal part of appliance．

溫度公差和使用壽命(Working Temperature Tolerance and Working Life)

最小通斷溫差(Min。 Temperature Differential)

注：1．上述的通斷溫差是指斷開溫度標稱值與接通溫度標稱值之差，最大可生產的溫差為70℃~100℃。
　　2．除上述外，我公司可按客戶對性能或外形結構的特殊要求進行專門生產。
Note：1．The above temperature differential is the differential between open temperature value and closed temperature value．The max．temperature differential in our factory is 70℃~100℃。
　　　2．In addition。we can manufacture thermostats up to the special requirement of characteristics and dimension from our clients．